Contact Us   |   Sign In   |   Join ICAC
VOC Controls

VOC controls include all technologies which either collect the VOCs for recovery and reuse, or destroy the VOCs.
If the VOCs have recovery value, which typically implies single-VOC exhaust streams, and if the cost of recovery is less than the cost of purchasing new VOC, which typically implies relatively concentrated exhaust streams, then recovery makes sense. Carbon adsorption, scrubbing, and condensation are typical recovery techniques. Note that the installation and operation of a recovery technology may more than pay for itself if the recovery value of the VOC is high enough.

If the VOC stream has no recovery value, if, for example, it is a mixture, or if there are disposal concerns, such as for toxic compounds, then destruction probably makes the most sense. Thermal and catalytic oxidation and biofiltration would be useful in this case.

Carbon Adsorption

Adsorption on activated carbon is useful for recovery of VOCs with intermediate molecular weights (typically about 45-130): smaller compounds do not adsorb well, and larger compounds cannot be removed during regeneration, which typically is by steam stripping. Adsorption is most effective at lower temperatures, so that cooling of hot exhaust gas streams may be necessary. Further, dehumidification of very humid streams may be necessary for the carbon to have the greatest capacity.
While carbon is the dominant adsorbent used, alumina, zeolites, and polymers have been used in some processes.

Carbon can also be used to remove compounds in a once-through process with off-site regeneration.

Thermal Oxidation

Thermal oxidation is the process of oxidizing combustible materials by raising the temperature of the material above its auto-ignition point in the presence of oxygen, and maintaining it at high temperature for sufficient time to complete combustion to carbon dioxide and water. Time, temperature, turbulence (for mixing), and the availability of oxygen all affect the rate and efficiency of the combustion process. These factors provide the basic design parameters for VOC oxidation systems.
There are three basic types of thermal oxidation systems: direct flame, recuperative, and regenerative.

Direct flame systems or flares rely on contact of the waste stream with a flame to achieve oxidation of the VOCs. These systems are the simplest thermal oxidizers and the least expensive to install, but require the greatest amount of auxiliary fuel to maintain the oxidation temperature, thus entailing the highest operating cost. Flares are useful for destruction of intermittent streams.

Recuperative thermal oxidation systems use a tube or plate heat exchanger to preheat the effluent stream prior to oxidation in the combustion chamber. Thermal recovery efficiencies typically are limited to 40-70% to prevent auto-ignition in the heat exchange package, which could damage the package. Supplemental fuel therefore is usually required to maintain a high enough temperature for the desired destruction efficiency. Recuperative systems are more expensive to install than flares, but have lower operating costs.

Regenerative thermal oxidation systems typically incorporate multiple ceramic heat exchanger beds to produce heat recovery efficiencies as high as 95%. An incoming gas stream passes through a hot bed of ceramic or other material, which simultaneously cools the bed and heats the stream to temperatures above the auto-ignition points of its organic constituents. Oxidation thus begins in the bed, and is completed in a central combustion chamber, after which the clean gas stream is cooled by passage through another ceramic heat exchanger. Periodically the flow through the beds is reversed, while continuous flow through the unit is maintained. Regenerative thermal oxidation systems are the most expensive thermal oxidizers to build, but the added capital expense is offset by savings in auxiliary fuel.

Catalytic Oxidation

Catalytic oxidation converts volatile organic compounds (VOC) into carbon dioxide and water, as do other oxidation processes, with no byproducts requiring disposal. Catalytic oxidation is well suited to applications with VOC concentrations ranging up to 25% of the lower explosion limit. With proper selection of catalyst, operating conditions, and equipment design, catalytic oxidation can attain VOC conversions of up to 99%. Advantages of this technology are low fuel usage, particularly with the proper choice of heat exchanger, little nitrogen oxide formation, given low operating temperatures, and little formation of partial oxidation products, such as carbon monoxide and aldehydes. Disadvantages include susceptibility to catalyst poisons, and the sensitivity of the catalysts to high temperatures.
Catalysts for VOC oxidation typically are either precious metals supported on ceramic or metal monoliths (honeycombs) or on ceramic pellets, or base metals supported on ceramic pellets. Catalyst life exceeds five years with the proper choice of catalyst, and may be extended with catalyst washing and regeneration techniques. Recent generations of catalysts have much longer lives and greater poison resistance than their forebears, and have greater capabilities, including the destruction of chlorinated organics.

As with any process, proper equipment design is essential to performance and operating cost. Typical catalytic oxidizer components include the catalyst housing, blower, burner, heat exchanger, controls, and stack. Small units are often skid-mounted and delivered to the site ready for installation.

As vent streams are often below the temperature at which catalytic oxidation is effective, most oxidizers use burners to preheat these streams to reaction temperatures, often from 400-800 °F. Heat is recovered using either recuperative or regenerative heat exchangers. As the latter can provide 95% heat recovery, streams with low VOC levels can be processed with minimal fuel usage.


Biofiltration is an oxidation process which is in common use abroad and which is beginning to find wide use in the U.S. There are hundreds of biofilters installed abroad, and probably dozens in the U.S.
In biofiltration, a VOC-containing air stream is passed through a biofilter, a filter bed on which bacteria or other microorganisms are supported. Biofilters have been as simple as beds of earth, peat, or sewage sludge. More recently used biofilters have been bacteria supported on manufactured supports such as activated carbon.

Biofiltration may provide very high VOC removal efficiencies, but is limited to concentrations below 2000 ppm, and works best for very low VOC concentrations, including odors. Very hot exhaust streams will require cooling upstream of the biofilter.

Cryogenic Condensation

Low temperature or cryogenic condensation is a process that can be used as an effective means for VOC emissions control. Cryogenic condensation technology is based on lowering the vapor pressure of a component by reducing the temperature of the process stream thus increasing the recovery of the components in the liquid phase.

Since nitrogen gas is widely used in the chemical process industry, is inert and is typically transported and stored in it's liquid state at low temperature and high pressure, it is a convenient media to use. The low temperature capability of liquid nitrogen allows for the design of highly efficient condensation systems. At temperatures below –120°F, the vapor pressure of most organic compounds is depressed sufficiently to condense 95 to 99+% of the compounds from a typical emissions stream. In addition, the vented nitrogen can be recycled for reuse within the plant.

Cryogenic condensation is well suited for VOC emission control because of its ability to respond instantly to changes in VOC flow rate and solvent loading. It can recover virtually any VOC species even under varying conditions. Cryogenic condensation can deal with all organics (even in the presence of water) and can function when the concentration and composition are changing over time. This flexibility makes it particularly suitable for VOC control in multi-product, multi-purpose plants where batch or continuous processes are employed.

Membership Management Software Powered by YourMembership  ::  Legal